Truetone 1 Spot
CS11
Art.Nr. 4087
€ 225,00
inkl. ges. MwSt., zzgl. Versandkosten
Versand Inland (Germany) € 5,90
Versandkosten international
Auf Lager
CS11 The most powerful 1 Spot PRO yet The 1 Spot Pro CS11 is the same size as the CS12, but with all new outputs and options. It doesn’t replace the CS12, but gives users more power and more available 9Vdc outputs. It also has “one more” output on the back, which allows users to connect the CS11 to Truetone’s new expansion boxes like the XP5 and XP8. It goes to 11… and so much more. Input Voltage The 1 SPOT Pro CS11 can be used anywhere in the world without the use of a step-up or step-down transformer. Like our 1 SPOT, it transforms wall voltage from 100-240VAC, and converts it into the stated voltages on the bottom of the unit. Cables The 1 SPOT Pro CS11 includes a generous assortment of cables and converter plugs. The cables are of various lengths, color-coded for easy cable management and with right angle plugs on the pedal end. Power cables (all are center pin negative polarity): (2) DC26 (5.5x2.1mm barrel plugs; 26” (660mm) – Purple (2) DC22 (5.5x2.1mm barrel plugs; 22” (559mm) – Blue (4) DC18 (5.5x2.1mm barrel plugs; 18” (457mm) – White (3) DC12 (5.5x2.1mm barrel plugs; 12” (305mm) – Yellow (1) MC2 Two 5.5x2.1mm barrel plugs with 5.5x2.1mm input socket. Converter Plugs: (1) CL6 – (5.5x2.1mm barrel input, 5.5x2.5 barrel output; reverse polarity) Green – for Line 6 DL4/M9/etc. and some Eventide pedals. (1) CYR – (5.5x2.1mm barrel input, 5.5x2.1 barrel output; reverse polarity) Red – reverse polarity converter (1) C35 – (5.5x2.1mm barrel input, 3.5mm male output; tip positive) Black – 3.5mm (1/8”) plug converter (1) CBAT – (5.5x2.1mm barrel input, Black battery clip output) Connects to battery clip wires inside pedals that do not have DC jacks. Do NOT connect to a battery! (1) C2.5 – Gray – 5.5x2.5mm plug converter - can be used for Line 6 HX series and POD Go Available Output Voltages: Outputs 1-2, 10-11: 9VDC (500mA) Outputs 3-4: 9VDC or 18VDC (100mA) Outputs 5-6: 9VDC or 12VDC (250mA) Outputs 7-9: 9VDC (250mA) Can the 1 SPOT Pro power my pedal? That question can best be answered by looking at the following questions and notes… Which output and settings do I use for my pedals? It is important for you to know the power requirements for your pedal. For every pedal that you are going to power via the 1 SPOT Pro CS11, you need to know the following: What is the voltage required by the pedal? Does the pedal require AC or DC voltage? What is the polarity of the pedal? (Center pin positive or negative.) These questions can usually be answered by: 1. Inspecting the pedal itself near the power jack. 2. Referring to the owner’s manual. 3. Checking online, or contacting the manufacturer 4. If your pedal can be powered by a 9Vdc battery, it can be powered by one of the 9Vdc outputs ( an exception being the Boss ACA pedals, see below). Notes on using certain pedals with the 1 SPOT Pro CS11: -Older Boss pedals marked “ACA” use outputs 5 or 6, set to 12Vdc. Newer Boss units marked “PSA” can be used with any 9Vdc output. -For pedals with a current draw higher than 400mA, please utilize outputs 1,2,10 or 11. To be sure about the current draw of your pedals, please use a Truetone mA Meter, sold separately. -Eventide Factor pedals and H9/H90 may be powered by any output with a rating of 250mA or higher, with the addition of the CL6 converter for proper DC jack tip size and polarity. -Line 6 M9 may be powered by outputs 1,2,10 or 11, but will also require the CL6 converter. -Line 6 M5 may be powered by outputs 1,2,10 or 11, without a converter plug. -Line 6 HX series and POD Go require a C2.5 converter. Please note, although they can be powered by outputs 1,2,10 or 11, it is recommended to power them from 2 of those outputs combined using a Truetone MC2 cable (included) to split the current load. -If additional analog 9Vdc pedals need to be powered, a Truetone Multi-Plug cable (sold separately) may be connected to any of the 9Vdc outputs depending on mA draw. -If additional pedals need isolation, you may purchase a Truetone XP5 or XP8 expansion box which connects to the 12Vdc jack on the back panel. The XP5 has 5 isolated and filtered outputs, while the XP8 has 8. -Pedals that do not have a power jack, yet are powered normally by a 9Vdc battery, may utilize any 9Vdc output, along with the CBAT converter. -Digitech Whammy: Version 5 or Whammy DT may be powered by outputs 1,2,10 or 11. Versions 1-4 cannot be powered by a CS11, unless you purchase the optional Truetone ACY-US cable (North America only) and use the original Digitech Whammy power supply. -Radial Tonebone 15Vdc pedals can be powered by outputs 3 or 4, switched to 18Vdc, using the Reverse Polarity Converter (CYR) included with the 1 SPOT Pro. Dimensions: 205 x 86 x 50mm (8.07 x 3.38 x 1.97”); 971 grams (2.14 lbs.) - weight and dimensions of power supply only, not including cables or packaging. Bedienungsanleitung